elektricni

ELECTRIC DETONATORS

ELECTRIC

Milisecond Electric Detonators are used for blasting hard and very hard materials, which as a result of their strong resonance effect achieve fair breakage of materials and make maximum use of the power of explosives. These detonators must not be used in an environment where there is high risk of ignition and methane explosion. DETAILED DESCRIPTION

Unit No Shell Length (Range) Delay time msed 20,23 Msed 30,34
0 52 0-0 0-0
1 67 20-23 30-34
2 69 40-46 60-68
3 71 60-69 90-102
4 74 80-92 120-136
5 76 100-111 150-170
6 78 120-138 180-204
7 80 140-161 210-238
8 82 160-184 240-272
9 84 180-207 270-306
10 84 200-230 300-340
11 89 220-253 330-374
12 89 240-276 360-408
13 89 260-299 390-442
14 89 280-322 420-476
15 89 300-345 450-510
16 89 320-368 480-544
17 89 340-391 510-578
18 89 360-414 540-612

 

Halfsecond Electric Detonators are used for blasting medium, hard and soft materials. Due to the long delay intervals, follows a successive discharge of a material which further results in reaching a larger scale granulation, adequate for transportation; and all the temblors are caused by the power of a single mine.а.

DETAILED DESCRIPTION

Unit No 1 2 3 4 5 6 7 8 9 10 11 12
Shell Length mm 67 69 71 74 76 78 80 82 84 87 89 89
Delay time psed 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000

 

NON-ELECTRIC DETONATORS

BIHNEL MS & BIHNEL LP

Non-Electric Detonators BIHNEL MS are used for precise and controlled blasting in road construction, exploitation of mineral resources and construction work above ground and underwater.
DETAILED DESCRIPTION

Brand Type Shell Length mm Delay time Interval
Ms0 50 0 25
Ms1 50 25 25
Ms2 50 50 25
Ms3 50 75 25
Ms4 52 100 25
Ms5 52 125 25
Ms6 52 150 25
Ms7 55 175 25
Ms8 55 200 25
Ms9 57 225 25
Ms10 57 250  25
Ms11 60 275 25
Ms12 60 300 25
Ms16 63 400 50
Ms18 65 450 50
Ms20 67 500 50

Non-Electric Detonators BIHNEL LP are used for underground mining and tunnel blasting, which require deceleration, so that the materials are being separated until the next detonation.
DETAILED DESCRIPTION

Brand Type Shell Length mm Delay time Interval
Lp-0 50 25 0
Lp-1 52 100 75
Lp-2 56 200 100
Lp-3 60 300 100
Lp-4 60 400 100
Lp-5 60 500 100
Lp-6 63 600 100
Lp-7 63 700 100
Lp-8 63 800 100
Lp-9 67 900 100
Lp-10 67 1000 100
Lp-12 67 1200 200
Lp-14 69 1400 200
Lp-16 71 1600 200
Lp-18 71 1800 200
Lp-20 71 2000 200
Lp-25 71 2500 500
Lp-30 71 3000 500
Lp-35 74 3500 500
Lp-40 76 4000 500
Lp-45 78 4500 500
Lp-50 80 5000 500
Lp-55 82 5500 500
Lp-60 84 6000 500

BLASTING CAP

BLASTING CAP & BIHNEL INITIATING TUBE

Blasting Cap, which is used for blasting dry surface and underground places to work, triggers a complete detonation of several explosive charges, i.e. it utilizes its explosive power to the fullest.
DETAILED DESCRIPTION

Type of DK Shell Material Shell Diameter (mm) Shell Length (mm)
DK – 8 Al 7.2 40
DK – 8 Cu 7.2 42

 

BIHNEL Initiating Tube as an efficient initiating device for detonators and connectors is suitable for surface and tunnel blasting.
DETAILED DESCRIPTION

Outside Diameter 3+ 0,15 mm
Inside Diameter 1.2 0.1 mm
Explosive Charge 15-20 mg/m
Impact sensitivity Impact insensitivity up to 60 Ј
Impulse Velocity 1800-2000 m/s
Detonation Transmission Tubing 4 cm (100%)
Force of Interruption 140 n
Tension Up to 250 %
Resistance to Mechanical Damage Meets the standards EN 13765-5 item 5.2.1
Operating Temperature Range -35 up to 40 c